CSDN博客

img colayungnew

EA700A 安装指导

发表于2004/10/20 11:43:00  1419人阅读

 

   

 

 

1、硬件安装:(详见快速安装手册)................................................................................ 3

2、软件设置:................................................................................................................. 3

21、路由模式的必要设置....................................................................................... 3

2.2、桥接方式的必要设置....................................................................................... 4

2.3、PPPoE  的设置:............................................................................................. 5

24、增加一条PVC的连接应用方法:.................................................................... 6

241 VC1的设置:....................................................................................... 6

242 VC2的设置:....................................................................................... 7


EA700A应用设置方法

 

1、硬件安装:(详见快速安装手册)

2、软件设置:

EA700A连线完成后,使用Telnet连接进入SMT设置菜单,EA700A缺省的IP地址为192.168.1.1,缺省的进入密码为“1234”。当成功进入SMT菜单后请按照下面的过程逐步设置。

21、路由模式的必要设置

首先应从ISP得到如下信息:

VPI/VCI号码,封装模式,复用模式,IP地址获得的方式(动态,还是静态)

然后,按照下面的范例填入相应的设置中。

 

Menu 1 - General Setup

            System Name= CHT

            Location=

            Contact Person's Name=

 

               Route IP= Yes

               Route IPX= No

               Bridge= No

 

 

Menu 4 - Internet Access Setup

                 ISP's Name= CHT

                 Encapsulation= RFC 1483<-按空格切换封装模式RFC1483PPPRFC2364

                 Multiplexing= LLC-based<-按空格切换复用模式

                 VPI #= 0   

                 VCI #= 33   写入相应的VPI/VCI

                 My Login= N/A

                 My Password= N/A

                 Single User Account= Yes

                 IP Address Assignment= Dynamic 按空格切换动态获得IP还是指定静态IP

                   IP Address= N/A               

                   ENET ENCAP Gateway= N/A

 

 

 

 

 

 

 

2.2、桥接方式的必要设置

当使用专线桥接方式时,都需要将EA700A设置为桥接方式

 

Menu 1 - General Setup

            System Name= CHT

            Location=

            Contact Person's Name=

 

               Route IP= No

               Route IPX= No

               Bridge= Yes

 

 

Menu 4 - Internet Access Setup

                    ISP's Name= CHT

                    Encapsulation= RFC 1483<-按空格切换封装模式

                    Multiplexing= LLC-based<-按空格切换复用模式

                    VPI #= 0   

                    VCI #= 33   写入相应的VPI/VCI

                    My Login= N/A

                    My Password= N/A

                    Single User Account= No 按空格切换为No

                    IP Address Assignment= N/A

                      IP Address= N/A              

                    ENET ENCAP Gateway= N/A

 

 

Menu 11.1 Remote Node Setup

     Rem Node Name= ChangeMe             Route= No   <-按空格切换为No

     Active= Yes                           Bridge= Yes <-按空格切换为Yes

 

     Encapsulation= RFC 1483              Edit PPP Options= N/A

     Multiplexing= LLC-based               Rem IP Addr= N/A

     Incoming:                           Edit IP/IPX/Bridge= No

       Rem Login= N/A

       Rem Password= N/A

     Outgoing:                            Session Options:

       My Login= N/A                            Edit Filter Sets= No

       My Password= N/A

       Authen= N/A

 

 

2.3、PPPoE  的设置:

 

 首先应从ISP得到如下信息:

确定本条线路已经在局端设置成为PPPoE拨号上网方式;

PPPoEVPI/VCI(很多地区专线模式和PPPoE拨号模式使用不同的VPI/VCI,);

PPPoE的用户名/密码 (格式为:username@servicename / password)

 

1.    Menu 1 IP routing = Yes ; Bridge = No

2.    Menu 4

Menu 4 - Internet Access Setup

 

                    ISP's Name= ChangeMe

                    Encapsulation= PPPoE

                    Multiplexing= LLC-based

                    VPI #= 2

                    VCI #= 22

                    Service Name= cso

                    My Login= kevin

                    My Password= ********

                    Single User Account= Yes

                    IP Address Assignment= Dynamic

                      IP Address= N/A

                    ENET ENCAP Gateway= N/A       

 

3.    Menu 4 的设定会自动映射到Menu 11 ,但还应注意在menu 11中设定为路由模式。

                    Menu 11.1 - Remote Node Profile

 

     Rem Node Name= ChangeMe              Route= IP

     Active= Yes                          Bridge= No

 

     Encapsulation= PPPoE                 Edit PPP Options= No

     Multiplexing= LLC-based              Rem IP Addr= 0.0.0.0

     Incoming:                            Edit IP/IPX/Bridge= No

       Rem Login=

       Rem Password= ********

     Outgoing:                            Session Options:

       My Login= kevin                      Edit Filter Sets= No

       My Password= ********                PPPoE Idle Timeout(sec)= 0

       Authen= CHAP/PAP                     PPPoE Service Name= cso

       Schedule Sets=       

 

4.    对于局域网的设置:

当指定EA700ADHCP server时:在PC上设定为自动获取IP地址。

 

当不指定EA700ADHCP server时,请将局域网内的PCIP地址与Menu 3.2EA700ALAN IP地址设在同一网段内,并在PC上将Modem设定为缺省网关。

 

24、增加一条PVC的连接应用方法:

 

 

 


PC ------EA700A------------------DSLAM ————ISP---------Internet

|______VoD server .

 

 


    如果在DSLAM后面,到VoD server ISP 使用不同的VC则需要首先在Menu1Menu4中按照桥接模式作好设置,然后在menu11做两条VC的设置:

其中的VPI/VCI应该是由局端提供

这里假设局端给出的设置为:

VC1VPI/VCI 0/33 bridge ISP

VC2VPI/VCI 0/34 bridge VoD server .

 

       Menu 11  ---- Remote Node Setup

 

1.   ChangeMe (ISP,SUA)

2.   __________________

3.   __________________

4.   __________________

5.   __________________

6.   __________________

7.   __________________

8.   __________________


 

241 VC1的设置:

Menu 11选择1进入第一条VC的设置:

                         Menu 11.1 - Remote Node Profile

 

     Rem Node Name= bridge1               Route= None

     Active= Yes                          Bridge= Yes

 

     Encapsulation= RFC 1483              Edit PPP Options= N/A

     Multiplexing= LLC-based              Rem IP Addr= N/A

     Incoming:                            Edit IP/IPX/Bridge= Yes----进入下一级菜单

       Rem Login= N/A                                                                            见下图Menu11.3

       Rem Password= N/A

     Outgoing:                            Session Options:

       My Login= N/A                        Edit Filter Sets= No

       My Password= N/A                     PPPoE Idle Timeout(sec)= N/A

       Authen= N/A                          PPPoE Service Name= N/A

 

 

Menu 11.3 - Remote Node Network Layer Options

 

 VPI/VCI (LLC-mux or PPP/PPPoE Encap):       IPX Options:

         VPI #= 0                           Rem LAN Net #= N/A

         VCI #= 33  输入第一条VC        My WAN Net #= N/A

     IP Options:                            Hop Count= N/A

       Rem IP Addr: N/A                     Tick Count= N/A

       Rem Subnet Mask= N/A                 W/D Spoofing(min)= N/A

       My WAN Addr= N/A                   SAP/RIP Timeout(min)= N/A

       Single User Account= N/A             Dial-On-Query= N/A

       Metric= N/A

       Private= N/A

       RIP Direction= N/A

         Version= N/A                     Bridge Options:

       Multicast= N/A                       Dial-On-Broadcast= N/A

       IP Policies= N/A                     Ethernet Addr Timeout(min)= 0

 

 

 

 

 

 

242 VC2的设置:

       Menu 11选择2进入第二条VC的设置:

Menu 11.1 - Remote Node Profile

 

     Rem Node Name= bridge2               Route= None

     Active= Yes                          Bridge= Yes

     Encapsulation= RFC 1483              Edit PPP Options= N/A

     Multiplexing= LLC-based              Rem IP Addr= N/A

            Incoming:                           Edit IP/IPX/Bridge= Yes----进入下一级菜单

              Rem Login= N/A                                                                 见下图Menu11.3

       Rem Password= N/A

     Outgoing:                            Session Options:

       My Login= N/A                        Edit Filter Sets= No

       My Password= N/A                     PPPoE Idle Timeout(sec)= N/A

     Authen= N/A                          PPPoE Service Name= N/A

 

Menu 11.3 - Remote Node Network Layer Options

 

     VPI/VCI (LLC-mux or PPP/PPPoE Encap):IPX Options:

         VPI #= 0                           Rem LAN Net #= N/A

         VCI #= 34   输入第二条VC       My WAN Net #= N/A

     IP Options:                             Hop Count= N/A

       Rem IP Addr: N/A                     Tick Count= N/A

       Rem Subnet Mask= N/A                 W/D Spoofing(min)= N/A

       My WAN Addr= N/A                     SAP/RIP Timeout(min)= N/A

       Single User Account= N/A             Dial-On-Query= N/A

       Metric= N/A

       Private= N/A

       RIP Direction= N/A

         Version= N/A                     Bridge Options:

       Multicast= N/A                       Dial-On-Broadcast= N/A

       IP Policies= N/A                     Ethernet Addr Timeout(min)= 0

 

在用户的PC上将PCIP地址指定为与VoDServer同一个网段,当用户需要上网时,就使用PPPoE的拨号软件拨号。

 

地址:华星工业村4号楼2

电话:057185124807

邮编:310013

阅读全文
0 0

相关文章推荐

img
取 消
img